TPU 6650.沈阳 PC-1220 、ABS VE-0857 、‖。TPE TF5BNA 、PPS V170N3 、‖。PA6 1325GVS FEP NP1101 、TPE DGX7367 、→，EMA 1214AC 、→，PP RA1E10h 、→，EMAA 20B 、‖。PP H7700 、HDPE MR80 、HDPE M300054 、PA66 PA301G3 、POM F10-01 、→，POM FX-11J 、PMMA V045-68177 、ASA XC811-HW 、‖。TPV 9101-65 、PBT CL2045 、TPU E1150 、LDPE HP0322N 、PC 955 、→，LDPE 3026K 、PC DX07350 、‖。PBT 2000 、TPV 211-73 、TPU A92E4694 、PP 4720XWZ 、PC-1220 、‖。PP M3865 PPO PX1860 、PP FB2511 、‖。PC TP-50 、ABS GL-4 、→，PP R12232 、→，PLA V554X52 、TPE FX-9090UE 、TPE TC4NYZ ‖。 FL00226CC 、PBT 1100-211MB 、‖。PA66 KDR1021 PTFE L-5F 、‖。PMMA 80N 、PP SFT315 、PP 6231-20 、→，LCP V400P 、PC 141R-111 、‖。PC GN-1002FA KPA1 、→，PLA HT16WT6652 、PC DE1-1 、‖。PC/ABS CM6240-701 、‖。PP 5014L 、→，PPE 730G10L 、→，PLA 124790F 、‖。PC LV-2225Y 、→，CA 398-3 PA610 QP004 、PA66 AKV35LTH3.0 、PA66 RFL4026 、PC SFX173RU 、COC 790R 、→，PP EE108AE 、‖。ABS VP-10J ‖。 UE639-04 、‖。PA6 PF007 PPO PX2801Z-701 、‖。POM C9021GV3/30TF2 、EVA 631 、‖。PA66 RFL34 、PP 2900H 、→，PP J1400 、→，PC NX85T-10 、PC/ABS EXCY0297 、‖。ASA PW-957 、 TPU 6650.沈阳Optical properties of PMMA 1, visible light: high transmittance of visible light. PMMA is the best polymer transparent material at present, and its visible light transmittance is 92%, which is [1] higher than that of glass. 1. ultraviolet light: quartz can be completely ultraviolet light, but the price is high, ordinary glass can only pass through 0.6% ultraviolet ray, but PMMA can pass through 73%. PMMA can't filter out ultraviolet (UV). Ultraviolet light penetrates PMMA, and part of the manufacturer [2] is coated on the surface of the PMMA to increase the effect and properties of the UV light. On the other hand, PMMA has better stability than polycarbonate in the condition of ultraviolet light irradiation. 2. infrared: PMMA allows infrared rays less than 2800nm wavelengths to pass through. Longer wavelengths of IR, less than 25000nm, are basically blocked. There is a special colored PMMA that allows a specific wavelength of IR to pass through and block visible light, (used for remote control?or?heat, etc.). The POM enhanced POM The main reinforcement materials are glass fiber, glass ball?or?carbon fiber, and glass fiber is most commonly used. The mechanical properties of the reinforced glass can be increased by 2~3 times and the hot deformation temperature is increased by 50 degrees?or?more. The high oil POM Adding graphite, F4, molybdenum disulfide, lubricating oil and low molecular weight PE to POM can improve its lubrication performance. For example, adding 5 copies of F4 in POM can reduce the friction factor by 60%, and increase the wear resistance by 1~2 times. In addition, the addition of liquid lubricating oil in POM can greatly improve the wear resistance and the limit of PV. In order to improve the dispersing effect of oil, the oil absorption carrier, such as carbon black, barium hydroxide, and ethylene propylene rubber, should be added. The friction of adding 5% oil POM is increased by 72%, and the limit PV can reach 3.9MPa m/s (pure POM is 0.213MPa m/s), which is 3~20 times that of other engineering plastics. PPO B has good electrical properties in a wide range of temperature and frequency. It has no hydrolysis and shrinkage, and has no self extinguishment. It is resistant to inorganic acid, alkali, aromatic hydrocarbon, halogenated hydrocarbon and oil. It is prone to swelling?or?stress cracking. C, it has the advantages of large rigidity, high heat resistance, refractory, high strength and so on. D and polyether have the advantages of wear-resistant, non-toxic, and resistant to pollution. Dielectric constant and dielectric loss of E and PPO plastic materials are among the smallest varieties in engineering plastics. They are hardly affected by temperature and humidity. They can be used in low, medium and high frequency electric fields. The load deformation temperature of F and PPO can reach more than 190 degrees C, and the embrittlement temperature is -170 C. G, its main shortcomings are poor melt fluidity and difficult processing.。